T 1018/05 25-09-2007

Reasons for the Decision

1. The appeal is admissible.

2. Sufficiency of disclosure.

2.1 The Board agrees with the view of the Opposition Division (see point 5 of the decision under appeal), which was not disputed, that independent claim 1 covers three variants of rotating the cylindrical member and the roller relative to each other, namely:

(a) the cylinder is fixed and the roller rotates;

(b) the cylinder rotates and the roller is fixed;

(c) both the cylinder and the roller rotate;

whereby in each case a relative rotation is generated which allows the formation of an end portion having a reduced diameter and an oblique axis as compared to the cylindrical member.

It is not disputed that the embodiments of the invention described in the patent in suit only relate to variant (a). The Opposition Division considered that the performance of the variants (b) and (c) would require inventive skill and held therefore that the invention could not be performed over the whole area claimed without undue burden.

In accordance with the established case law of the boards of appeal (see e.g. T 206/83, point 5; further see in particular decision T 1040/03 of Board 3.2.01, which concerns a similar case between the same parties involved in this appeal, point 2.2), a detailed disclosure is not necessary if the skilled person, who has common general knowledge at his immediate disposal, is capable of putting the invention into practice without the burden of exercising inventive skill. This principle obviously extends to all variants encompassed by a claim.

In the communication annexed to the summons to oral proceedings the Board expressed the view that working tables combining various linear and rotational axes were generally known in the technical field of machine tools and that variations from a specific design and adaptations to a particular use were matters of normal design procedure. This view was not contested by the parties and therefore the Board sees no reason to reconsider it. Accordingly, the skilled person seeking to put into practice the above-mentioned variants (b) and (c), noting that these variants require the rotation of the cylindrical member about an axis which does not coincide with the central axis thereof, would obviously consider the use of known working tables combining various linear and rotational axes. As is generally known, rotation about these axes can be actuated simultaneously by means of a suitable control. In such case, the adaptation of the working tables to generate the required movement of the workpiece (cylindrical member) does not require more than an adaptation of the control (such as e.g. entering a particular program to a computerized control) based on geometrical considerations, a task for which normal skills only are necessary. It follows that the skilled person could put into practice the contested variants (b) and (c) without the burden of exercising inventive skill.

2.2 The Opposition Division further held that the patent only disclosed how to carry out the first variant (a) for the particular case in which the forming target axis Xe and the main axis Xr have been set such that they coincide and that the invention could not be carried out when these axes were in the position according to Fig. 6, i.e. at a distance from each other.

In the Board's judgment claim 1 is not limited to the embodiment of Fig. 7, where the main shaft is displaced from its starting position shown in Fig. 6 such as to coincide with the axis Xe, which is the oblique axis of the resulting end portion having a symmetrical tapered portion 4b and a cylindrical portion 4c as shown in Fig. 8. The wording of claim 1 neither requires displacing an axis nor obtaining a tapered portion which must be symmetrical about the axis of the reduced end portion. Moreover, the possibility of carrying out the spinning process with the axes Xe and Xr as shown in Fig. 6 is explicitly disclosed in the patent in suit (see paragraph [0024]). It is true that such possibility is described as having disadvantages, namely because of the impacts received by the cylinder, causing vibration and noise, due to the fact that the roller abuts on only a part of the outer surface of the cylinder for any substantial period of time ("a long period of time"), and the need for a large forming tool if the distance between the axis Xe and the axis Xr is large. In fact, if the method of claim 1 of the patent in suit is carried out with the axis of the main shaft Xr (axis of rotation of the rollers 28) being at a distance from the axis Xe shown in Fig. 6, then at the beginning of spinning the lower portion of the cylindrical member is not deformed and the roller only works the upper portion thereof, whereby a discontinuous working is produced (hammering). However, when the radial displacement of the rollers is increased beyond that shown in Fig. 6, then a reduced diameter portion having an oblique axis Xr as its axis is formed. It is to be noted that if spinning is carried out starting from the position shown in Fig. 6, then the forming target axis is different from the axis Xe shown in Fig. 6: it coincides with the central axis Xr of the main shaft, whereby an asymmetrical tapered portion is obtained (note that according to Rule 29(7) EPC the reference signs in the claim between parentheses relating to the features in the drawings, such as Xe and Xr, are not to be construed as limiting the claim). Such embodiment of the claimed method might not be a preferred one; it is nevertheless an embodiment which can be carried out in practice, independently of how the relative movement between the cylindrical member and the roller(s) is generated (see above point 2.1).

2.3 The respondent did not provide any evidence in support of the allegations made about insufficiency, but rather relied on the apparent difficulties encountered when trying to carry out the method, such as the hammering action on the cylindrical member, especially when a high oblique angle was selected.

It is important in this respect to note that in the Board's view the above-mentioned established principle of the case law (see point 2.1 of this decision), according to which a detailed disclosure of all the variants encompassed by a claim is not necessary if the skilled person, who has common general knowledge at his immediate disposal, is capable of putting them into practice without the burden of exercising inventive skill, is not to be understood as also referring to those variants falling under the literal wording of the claim but which the skilled person would immediately exclude as being clearly outside the scope of practical application of the claimed subject-matter. That is, in cases where the skilled person would construe the claim as not extending to those variants. This is the case, for example, with claims including an open-ended range for a parameter where it is clear for a skilled person that the open-ended range is limited in practice. Such a claim must be seen as seeking to embrace values of the parameter as high as can be attained above a specified minimum level (see e.g. T 487/89, not reported, point 3.5). Values of the parameter not obtainable in practice would not be regarded by the skilled person as being covered by the claims and thus could not justify an objection of insufficiency of disclosure. More generally, in T 129/88 (OJ EPO 1993, 598) the Board, following T 487/89, observed that there may be circumstances in which the scope of a claim, notwithstanding the presence of open-ended features, is restricted by the presence of other features which impose a practical limit on the claim. See points 2.1.1 and 2.1.4.

In the present case, it would be evident for a skilled person that any inclination of the forming target axis leads, at least when starting the deformation, to a discontinuous deformation action of the rollers because an elliptical surface is initially presented to the rollers. This is independent of the choice of any of the three variants (a) to (c) referred to above and in fact represents per se a difficulty in practice, because it imposes certain practical limitations on the method and the apparatus used, in particular as compared to the conventional spinning where a circular surface is presented to the rollers.

The Board accepts the respondent's argument that a literal reading of the claim includes possibilities which are not feasible in practice without using further means not defined in the claim. However, due to the limited number of variables involved in the process (in particular the tube specifications, namely material, wall thickness and diameter; inclination and position of the forming target axis; deformation speed; characteristics of the apparatus used), the skilled person only needs to apply straightforward considerations to understand what are the practical limitations of the claimed method and, as a consequence, to establish the range of application of the claimed method with sufficient certainty.

The literal wording of claim 1 for example encompasses forming a very short, very small diameter end portion having an oblique axis strongly inclined (e.g. with an inclination angle >60º) against the central axis of a cylindrical member having a large diameter. Albeit that this is a theoretical possibility covered by the literal wording of claim 1, the skilled person would recognize that this possibility is not feasible in practice due to practical, unavoidable constraints. In particular, it is evident that the rollers must have certain dimensions in order to apply the required deformation load and that these dimensions imply geometrical limitations for the shape of the end portion to be achieved.

2.4 Claim 9 relates to an apparatus for forming an end portion of a cylindrical member by spinning comprising first driving means for moving at least one of said cylindrical member and said at least one roller relative to each other. For the above-mentioned reasons, the skilled person would have no difficulties in providing suitable driving means for obtaining the required relative movement, independently of whether it is the cylindrical member, the roller, or both that are rotated. Moreover, the claimed apparatus could perform the spinning of an end portion of a cylindrical member independently of any relative displacement of the forming target axis Xe and the main axis Xr, as shown in Fig. 6, such that they coincide.

2.5 It follows that the European patent discloses the invention in a manner sufficiently clear and complete for it to be carried out by a person skilled in the art.

3. Novelty

3.1 Document D1 undisputedly discloses a method and apparatus according to the preamble of claims 1 and 9, respectively. The Board agrees with the technical interpretation of D1 made by Board 3.2.01 in the above-mentioned decision T 1040/03. As stated in points 3 and 3.1 of that decision, it cannot be inferred from Fig. 4 of D1 that the tapered end portion is eccentric. Therefore, the disclosure of D1 can only be seen as related to the conventional spinning method (see par. [0002] of the patent in suit) in which an end portion is formed which is coaxial with the cylindrical member. Accordingly, D1 does not disclose the step and the means for forming a reduced diameter portion of a cylindrical member having an oblique axis inclined against the central axis of the cylindrical member.

3.2 P1 is undisputedly state of the art according to Article 54(3) EPC only in respect of subject-matter disclosed in the first priority application JP308240/97, which is document P2 on file. P1 discloses a method for forming a cylindrical eccentric end portion of a cylindrical member by spinning, see e.g. Fig. 5 of P1 and Fig.6 of P2. Claim 1 of the patent in suit requires that the at least one roller is rotated about a forming target axis (see the preamble of claim 1) and that said forming target axis is inclined against the central axis of the cylindrical member (see characterising portion of claim 1). However, in the method according to P1, the axis of the cylindrical member and the forming target axis about which the rollers rotate are always parallel.

In this respect it is noted that the argument of the respondent according to which the method of P1 corresponds to that according to claim 1 of the patent in suit because in P1 the axis of the resulting eccentric end portion is inclined against the central axis of the cylindrical member, fails because the features of the claimed method must be compared with those of the method disclosed by P1, not the features of the product, and P1 clearly discloses that the eccentric portion is obtained with the axis of rotation of the rollers being parallel and not inclined with respect to the central axis of the cylindrical member.

Furthermore, P1 does not disclose the feature of claim 9 according to which the claimed apparatus comprises means adapted to rotate at least one of said cylindrical member and said main shaft relative to each other to produce an oblique angle between the central axes of said cylindrical member and said main shaft.

3.3 It follows that the findings of the Opposition Division in respect of novelty over D1 and P1 (see points 2 and 3 of the decision under appeal) are correct.

4. Inventive step

4.1 The Board also agrees with the finding of the Opposition Division (see point 4 of the decision under appeal) that the subject-matter of claims 1 and 9 involves an inventive step in the light of D1.

4.2 The teaching of D1 is indeed limited to forming a reduced diameter end portion which is coaxial with the main body of the cylinder and there is no indication in D1 suggesting to the skilled person that the known spinning process could be used not only for forming the reduced diameter end portion of the cylindrical member but also to generate an inclined axis for said end portion when starting from a cylindrical member having a straight axis. This recognition is also not rendered obvious by the mere fact of knowing (from common general knowledge, see point 2.1. above) that working tables combining various linear and rotational axes exist. Nor is it rendered obvious by the request from industry to provide a cylinder with an oblique reduced diameter end portion, as this request per se does not indicate the claimed solution and moreover a different solution for this request already exists in the art (see par. [0005] of the patent in suit: forming separate components by press working and then connecting them by welding or the like).

5. The additional prior art filed in the appeal proceedings

5.1 The above conclusions are based on the prior art mentioned in the decision under appeal. With its letter of reply to the grounds of appeal the respondent referred to documents D2 and D3 which were not considered by the Opposition Division. D2 was cited in the search report but does not form part of the opposition or opposition appeal proceedings (see T 536/88). D2 and D3 must therefore be regarded as late-filed.

5.2 It is well established that a late-filed prior art document may be admitted and considered at the Board's discretion (see Case Law of the Boards of Appeal of the European patent office, 5th edition 2006, VI.F.2). In exercising its discretion the Board will in first place have to consider if the document is prima facie highly relevant in the sense that it is highly likely to prejudice maintenance of the European patent.

5.3 In the present case the Board judges that D2 and D3 are not prima facie highly relevant because neither of them relates to a spinning process used not only for forming a reduced diameter end portion of a cylindrical member but also to generate an axis inclined against the central axis of said cylindrical member. According to D2, spinning is performed on a work's protuberance which is already provided with an inclination, and according to D3 spinning is performed on the end portions of a curved pipe.

D2 and D3 are therefore disregarded pursuant to Article 114(2) EPC.

6. It follows that the grounds of opposition do not prejudice the maintenance of the patent unamended.