T 2670/18 14-10-2020

Reasons for the Decision

1. Applicable Rules of Procedure of the Boards of Appeal

1.1 The revised Rules of Procedure of the Boards of Appeal (RPBA 2020) entered into force on 1 January 2020 (Articles 24 and 25(1) RPBA 2020). Subject to the transitional provisions (Article 25 RPBA 2020), the revised version also applies to appeals pending on the date of the entry into force. In the present case the statement of grounds of appeal was filed before 1 January 2020. Thus, Article 12(4) to (6) RPBA 2020 does not apply, and instead Article 12(4) RPBA 2007 applies to the grounds of appeal (Article 25(2) RPBA 2020).

1.2 Since the Board communication pursuant to Rule 100(2) EPC has been notified after 1 January 2020, Article 13 RPBA 2020 is to be applied for questions regarding any amendment to the appellant's appeal case in response to the communication.

2. Main and auxiliary request I - Consideration in the appeal proceedings

2.1 The main request and auxiliary request I respectively correspond to main request a and main request b already filed before the examining division with letter of 30 April 2018 in response to the summons to oral proceedings.

2.2 Since the examining division based its decision on main request a and main request b, the main request and auxiliary request I must be considered in the appeal proceedings.

3. In its communication pursuant to Rule 100(2) EPC, the Board set out and reasoned its intention not to allow the main request and auxiliary request I, as follows (points 8 and 9):

"8.1 Since the purpose of Article 84 EPC is to ensure legal certainty as to the actual scope of protection conferred by a claim, the meaning of the features recited in a claim should be clear for the skilled person in the art from the wording of the claim alone.

8.2 The Board shares the view of the examining division that claim 1 does not meet the clarity requirement of Article 84 EPC.

8.3 In a nutshell, claim 1 defines a threaded joint for steel pipes comprising a pin (3) and a box (1) with mating threaded portions (7, 5), mating torque shoulder portions (12, 14) and mating seal portions (31, 21) to provide a metal-to-metal seal.

8.4 Feature (g) of claim 1 requires that xp >= 5,08 mm, where

FORMULA/TABLE/GRAPHIC,FORMULA/TABLE/GRAPHIC

p(x) is a contact face pressure, x is an axial distance from a pin end, and x1 and x2 are respectively a lower limit and an upper limit of a domain of x corresponding to the seal portion (20).

8.5 In the context of claim 1, it is clear that x1 and x2 are the lower und upper limits of the seal portion while p(x) is the contact pressure between the outer peripheral surface (31) of the pin nose (8) and the seal face (21) of the box (1) in the seal portion.

8.6 Thus, it is apparent that xp corresponds to the average location of the contact pressure in the seal portion, i.e. the centre of pressure, and feature (g) requires that it is located at least 5,08 mm away from an axial end of the pin.

8.7 Whilst the centre of pressure is a known parameter in the technical field of fluid mechanics, it appears to be an unusual parameter in the relevant field of threaded joints for steel pipes, as argued by the examining division.

8.8 In the context of claim 1, xp is not clearly defined because p(x), x1 and x2 are functions of the load applied to the threaded joint, e.g. fluid pressure (internal and/or external), axial force (tension or compression), bending (buckling and/or wellbore deviation) and/or make-up torsion, and there is no mention in the claim of the conditions under which these parameters are to be measured or calculated. Thus, it is uncertain how the calculation of xp should actually be carried out. For instance, it is unclear whether xp >= 5,08 mm must be fulfilled for any load condition or only for a specific load condition which is undefined.

8.9 A skilled reader of the claim is thus left in doubt as to which position of the centre of pressure is actually covered by the claim language and which is not, so that it cannot be ascertained whether a given threaded joint falls within the scope of the claim or not.

8.10 The calculation of xp is further defined in the description of the application (paragraphs 16 and 17 of D0):

(h) p(x) is obtained as a function of x by performing

an FEA calculation that simulates LP2 of the

series A test of ISO 13679, wherein the element

size is in the range of 0.001 to 0.01 inches and

the box and the pin are elasto-plastic bodies, and

(i) x1 and x2 correspond to two intersecting points of

the outer peripheral surface (31) of the pin nose

(8) and the seal face (21) of the box (1) when

cross-sectional views of the pin and the box having

the same size are placed one on top of the other so

that the pipe axes and shoulder faces of the pin

and the box coincide with each other.

8.11 The Board shares the appellant's view that, in light of this definition, the skilled person would for the following reasons face no difficulty in determining xp.

8.11.1 They would understand that the expression "LP2 of the series A test of ISO 13679" refers to load point 2 of test series A defined in table 6 of International standard ISO 13679:2002, namely a combined load of axial tension and internal pressure corresponding to hold point 2 in the first quadrant of the load path of test series A as shown in figure 13 or 14. The abbreviation "LP" is used in this standard to designate any load point (page 7). Even though the abbreviation "LP2" is used in the standard to designate limit load test path 2 defined in section 7.5.2 and shown figures 18 and 19 (page 7), namely a test under axial compression with external pressure increasing to failure, it is apparent that the expression "LP2 of the series A test" cannot refer to this limit load test. In fact, among eight limit load tests defined in the standard, limit load test path 2 is applied to demonstrate connection performance beyond the sealability tests according to test series A and C (table 2) and it is defined independently of these tests. The above understanding of the abbreviation "LP2" in the context of paragraphs 16 and 17 of the application appears to be confirmed by the reference to "LP12" in table 1 of the application, which can only refer to load point 12 of test series A, since there does not exist any limit load test path 12.

8.11.2 The skilled person would know that finite element analysis can be used to simulate the test procedures defined in standard ISO 13679:2002 (section 7.4.1, "Limit load tests may be useful for correlating with finite element analysis data") and they would understand that, in paragraphs 16 and 17 of the application, the abbreviation "FEA" means "finite element analysis", whereby the statements "the element size is in the range of 0.001 to 0.01 inches" and "the box and the pin are elasto-plastic bodies" refer to the FE modelling of the joint structure and material.

8.11.3 Whilst finite element analysis to simulate load point 2 of test series A of ISO 13679:2002, and thus obtain p(x) under this specific load condition, may involve challenging issues such as modelling of the joint structure, the material and the load, the Board sees no reason to doubt that this would be a routine task for the skilled person, as submitted by the appellant with reference to A3. The skilled person would thus be able to calculate p(x), x1, x2 and thus xp and thereby make a meaningful comparison with the prior art.

8.12 However, this special meaning of p(x), x1, x2 and xp is not suggested by the wording of claim 1 of the main request and there is no reason to read it into the claim.

8.13 The above objection would be overcome, if claim 1 were to be amended so that the definition of p(x), x1, x2 and xp is clear from the wording of the claim alone.

8.14 This is important because it is only the claims of the patent, not the description, which will be published in all the official languages of the EPO (see the Guidelines for Examination in the EPO, 2019, F-IV, 4.2).

9. The above objection under Article 84 EPC applies also to auxiliary requests I and II. The definition of x1 and x2 is not clear from the amended wording of claim 1 according to either auxiliary request."

4. In the absence of any counter-arguments in the appellant's response dated 31 August 2020, the conclusions reached by the Board in its communication pursuant to Rule 100(2) EPC continue to apply. Hence, neither the main request nor auxiliary request I can be allowed.

5. Auxiliary request II - Admissibility in the appeal proceedings

5.1 The appellant filed new auxiliary request II in response to the Board communication pursuant to Rule 100(2) EPC.

5.2 The Board exercised its discretion pursuant to Article 13(2) RPBA 2020 to admit this new request into the appeal proceedings for the following reasons.

5.3 The claim of the new auxiliary request II differs from that of auxiliary request II filed with the statement of grounds of appeal in that the definition of x1 and x2 of the integral in feature (g) of the claim has been introduced. This amendment is in response to the objection under Article 84 EPC which was raised for the first time in the Board communication pursuant to Rule 100(2) EPC (points 8.12 to 8.14 above).

5.4 The amendment to the claim clearly overcomes all outstanding objections without introducing new issues.

6. The Board is satisfied that the amendments to the claim are supported by the information in the application documents as originally filed (Article 123(2) EPC), as indicated by the appellant (see points IX-b) and IX-c) above).

7. Contrary to the examining division (see decision under appeal, point 2.3 of the reasons), the Board is also satisfied that the application discloses the claimed invention in a manner sufficiently clear and complete for it to be carried out by the skilled person (Article 83 EPC). As explained above, the Board shares the appellant's view that, following the guidance provided in the application and using common general knowledge, the skilled person would be able to calculate p(x), x1, x2 and thus xp and thereby make a meaningful comparison with the prior art. In particular, even though finite element analysis to simulate load point 2 of test series A of ISO 13679:2002 and thus obtain p(x) under this specific load condition may involve challenging issues such as modelling of the joint structure, the material and the load, the Board sees no reason to doubt that this would be a routine task for the skilled person, as submitted by the appellant. In the absence of any serious doubts substantiated by verifiable facts, there is no reason not to believe that the skilled person, following the guidance provided in the application and using common general knowledge, would be able to put the claimed invention into practice.

8. Remittal of the case

8.1 In its communication pursuant to Rule 100(2) EPC, the Board set out and reasoned its intention to remit the case to the examining division, as follows (point 12):

"12. Should the appellant file amendments to the claims which overcome the above objection under Article 84 EPC, the Board considers that it would be appropriate to remit the case to the examining division for further prosecution (Article 111(1) EPC), as requested by the appellant.

Even though a board normally does not remit the case (Article 11 RPBA 2020), special reasons are apparent in the present case for doing so. In particular, the appealed decision only deals with objections of lack of clarity, insufficient disclosure and added subject-matter, and the question of whether or not the claimed invention is novel and inventive in light of D1 to D3 has not been addressed in the decision. It is the primary object of the appeal proceedings to review the appealed decision in a judicial manner (Article 12(2) RPBA 2020), not to conduct a complete examination of the application."

8.2 The appellant did not contest the above conclusions of the Board and in fact, requested that the case be remitted to the examining division to decide on patentability.

8.3 Hence, the case is remitted to the examining division for further prosecution on the basis of the amended claim of auxiliary request II.