T 1056/14 08-12-2017

Reasons for the Decision

1. Admissibility of the opposition and appeal.

The objections raised in the written procedure were withdrawn by the respondent during the oral proceedings. The Board has checked that the formal requirements are met. Therefore, the appeal is admissible.

2. Insufficiency of disclosure, Article 100(b) EPC, Extended subject-matter, Article 100(c) EPC

Both of these objections constitute fresh grounds of opposition since they were not made at the time of filing the opposition and were not subject of the opposition proceedings. Since the respondent has not consented to their admission into the appeal proceedings they cannot be considered by the board (see G9/91, Reasons, paragraph 18, OJ 1993, 408).

3. Interpretation of the subject-matter of claim 1- new and/or unusual parameters

Claim 1 is characterised by specifying ranges for the two parameters:

(i) "head density"

(ii) "bulk locking ratio"

Neither of these parameters is actually defined in the claim.

3.1 In its letter of 18 November 2014 (see page 19, line 3), the respondent states that "the inventors devised a new technique and coined a new term, namely "bulk locking ratio". Thus, the "bulk locking ratio" is clearly a new parameter which is defined at paragraph [0062] of the patent:

"Bulk locking ratio is calculated similarly, except that it is only analyzed for arrays in which the fastener element stems are spaced close enough to prevent a head trapped in a receptacle, defined between four adjacent stems in two or three adjacent rows, from moving laterally out of the receptacle. At each analysis position of the two overlapped patterns, what is counted is the number of fastener element heads of the duplicate that are within receptacles of the original. A head of the duplicate is said to be within a receptacle of the original if the entire extent of any flat portion of the head surface is within a polygon connecting the centers of all of the fastener elements defining the receptacle. Such fastener element heads are said to be "locked" against gross lateral movement, even though they may freely move within the receptacle. For example, most of the fastener elements of the far left row of the duplicate in Fig. 11B are locked between fastener elements of the original, while none of the fastener elements of the duplicate in Fig. 11 C are locked."

Thus, although theoretically a polygon can be drawn between three adjacent stems, it is clear that the polygon in question is that connecting the centers of all the fastener elements defining the "receptacle" (or "pocket" in the claim language) which is defined as being between four adjacent stems as shown below. Therefore, in the context of the patent, in particular when reading claim 1, the bulk locking ratio is to be read accordingly.

FORMULA/TABLE/GRAPHIC

3.2 The board agrees with the respondent that "head density" is a straightforward parameter which the skilled person would have no difficulty in understanding since it simply relates the area of the heads of the fastener elements to the base. Consequently, the maximum theoretical upper limit is 50%, as given in the patent (see column 1, lines 26 to 27) since at greater values the two strips could not be pressed together.

4. Alleged prior use

4.1 The appellant alleges that a touch fastener under the trademarks "Microduotec 25440" and "Duotec 41", which were the subject of the technical report submitted as A2, were sold to Berger GmbH, Binder Benelux and Binder Italia before the priority date of the patent.

4.2 According to the appellant, the "Microduotec 25440" product was also sold in a transitional period under another trademark "MICROPLAST". Both names appear on the various invoices of A3 and A4.

4.3 A3 comprises:

- a reply dated 6 February 2001 from Gottlieb Binder GmbH (the appellant-opponent) confirming the dispatch of a sample of MICROPLAST (Reg. Trademark) (MICRODUOTEC) material in response to the request of A. Berger GmbH &Co.KG dated 1 February 2001;

- invoice with voucher no. 32869 dated 5 March 2001 for 1078,10 DM for 1470m of 50mm wide "Microduotec" self-adhesive product, invoice also comprises an indication of delivery by DPD-Paket with a date of 23 February 2001 to A. Berger GmbH & Co.KG in D-Krefeld

- invoice with voucher no. 36094 dated 27 April 2001 for 5442,26DM for 12680m of 25mm wide Microplast, MICRODUOTEC net weight 127kg; indication of delivery on 13 March 2001 to A. Berger GmbH & Co.KG in D-Krefeld;

- invoice with voucher no. 35435 dated 18 April 2001 for 445,90 Eur for 5200m of 15mm wide Microplast product, delivery note 043443 201342 and 50m of 20mm wide "Klettostar-Haft" delivery note 043444 201359 to "BINDER BENELUX BVBA" in B 2547 LINT - no dates mentioned in connection with delivery but delivery note numbers are given.

4.4 A4 comprises a further invoice:

- invoice dated 15 January 2002 with voucher no. 48259 for 492m of 50mm wide Duotec 41 and 492m of 90mm wide Duotec 41, indication of delivery on 2 January 2002 to BINDER ITALIA S.R.L in MILANO.

4.5 Therefore, the alleged prior use corresponds in fact to four separate sales of a product allegedly identical to those analysed in A2, and therefore novelty destroying for the claimed invention :

2 sales of Microduotec to A. Berger GmbH on 23 February 2001 and 13 March 2001;

1 sale of Microplast to Binder Benelux BVBA at a time around 18 April 2001;

1 sale of Duotec 41 to Binder Italia perhaps on 2 January 2002;

4.6 However, although the answers to the questions of what was allegedly made available to the public (Microplast (MICRODUOTEC), Duotec 41), where (in Krefeld, Lint, Milan), how (by sale) and by whom (the opponent) have all been supplied, it has not been established that the products sold under these trade marks according to A3 and A4 were the same as those tested in A2.

4.7 A2 reports on tests carried out to measure the head densities of Duotec 41 and Microduotec 25440 fasteners. The following values are given:

Microduotec 25440: 34,12%; and

Duotec 41: 26,89%

which both lie within the claimed range.

4.8 A further value, referred to as the "Verhakungsdichte", was only measured for the Microduotec 254440 sample. However, this value does not correspond to the bulk locking ratio, but rather to the "bulk engagement ratio" (see column 1, lines 27 to 33 of the patent specification). Thus, not only is it not sure whether the fasteners tested in A2 were the same as those identified in A3 and A4, but also the test report values given in A2 do not correspond to the bulk locking ratio parameter claimed.

4.9 According to the report, every head of the Microduotec 25440 sample engages with three neighbouring heads (also to be seen in figure 4 of A2). Thus, the sample of Microduotec 25440 tested is no more relevant than the material shown in figures 2a and 2b of E3 since it relates to a head being locked in a receptacle defined by a polygon drawn between three heads.

5. Hearing of witnesses

5.1 The appellant submitted that its right to be heard had been violated (without explicitly alleging a substantial procedural error) since the opposition division did not hear the witnesses offered to support its case concerning the alleged prior use. It also requested that the witnesses should be heard at the appeal stage.

5.2 However, the board considers such a hearing to be unnecessary since not only should the details concerning the bulk locking ratio parameter of the fasteners tested have been correctly provided in writing from the outset, but also the Microduotec product tested in A2 is, on the basis of the available information, clearly no more relevant than the disclosure of E3.

6. Novelty with respect to E3

6.1 Since the "bulk locking ratio" defined in claim 1 is a new parameter it is unsurprising that E3 does not contain any literal disclosure of it. Despite this, it still must be assessed whether any of the arrangements disclosed in the figures of E3 inevitably fall within the claimed range. In this situation, the onus to convincingly establish novelty over the embodiments (particularly figures 2a and 2b) illustrated in E3 lies with the respondent.

6.2 The board agrees with respondent that E3 does not disclose any arrangements in which the fastener element stems are spaced close enough to prevent a head trapped in a receptacle, defined between four adjacent stems in two or three adjacent rows, from moving laterally out of the receptacle. In the annotated figure 2a of E3 provided by the appellant it is evident that the fastener heads of the duplicate will only make contact with the two heads delimiting the hypothesised four stem pocket which are closest together. Thus, there is nothing to prevent lateral movement between the two heads which are furthest apart until the point at which the duplicate head becomes trapped in the true pocket defined by three adjacent stems.

6.3 Since the locking arrangements shown in E3, particularly figures 2a and 2b, 13a and 13b, all relate to receptacles or pockets defined between three stems, the bulk locking ratio of claim 1, which is specified as relating to pockets defined between four stems, is not disclosed.

6.4 Furthermore, a head density ratio of between 20 and 35% is not explicitly disclosed in E3. It is also not possible to derive this value directly and unambiguously from the figures since these are merely schematic and do not allow precise calculations to be made.

6.5 Therefore, the subject-matter of claim 1 as granted is new.

7. Inventive step

7.1 The embodiment shown in figures 2a and 2b of E3 is considered to be the closest prior art. The subject-matter of claim 1 differs from these known fasteners by the features of the characterising portion.

7.2 A head density of between 20 and 35% offers an optimum compromise between ease and security of engagement. Less than 20% and engagement is precarious, more than 35% and engagement is difficult requiring precise alignment and "superman thumb" levels of pressure.

A bulk locking ratio of at least 10% ensures that there is a sufficient number of heads trapped in the pockets to resist lateral movement.

7.3 Thus, a combination of the features of the characterising portion of claim 1 solves the problem of providing a fastener which can be easily pressed together yet resist lateral movement.

7.4 The board agrees with the appellant that the minimum value of the head density in the above arrangement must be well over 0% for there to be any chance of engagement and that the maximum value cannot be more than 50%, otherwise engagement becomes impossible. The effects of varying head density are well understood, too higher values leading to impractical levels of pressure being required to ensure engagement. Therefore, head densities of between 20 and 35% are values that the skilled person would arrive at by routine testing, when faced with the above problem.

7.5 However, there is nothing in E3 which would prompt the skilled person to combine this range of head densities with an arrangement in which the heads are trapped in pockets defined between four adjacent stems.

7.6 Faced with this problem, it would also not be obvious for the skilled person to seek to combine the teachings of E1 and E3 since E1 is not directed to self-engagement of a single pattern as in E3 and the patent, but rather to the engagement of one pattern with a different pattern, namely engagement of the pattern shown in figures 1 to 3 with the pattern shown in figure 4. Consequently, they present entirely different solutions to a common problem. Even if the skilled person were to consult E1 when searching for improvements to E3, the results obtained would not lead to the subject-matter of claim 1.

7.7 Thus, the subject-matter of claim 1 meets the requirements of Article 56 EPC since it involves an inventive step. Since there were no more objections based on further documents, the appeal is to be dismissed.